coelner/OpenLog
1
0
Fork 0
mirror of https://github.com/sparkfun/OpenLog.git synced 2024-09-19 16:40:14 +00:00
Code Issues Packages Projects Releases Wiki Activity

Adding 'read firmware version' example

Browse Source
This commit is contained in:
nseidle 2018-04-25 15:41:17 -06:00
parent e9b34ca4a9
commit d1aefc7c94
4 changed files with 207 additions and 5 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

105
firmware/Arduino_Examples/Example6_GetVersionNumber/Example6_GetVersionNumber.ino Normal file
View File

@ -0,0 +1,105 @@
/*
Example of creating a file, reading a file, and reading the disk properties on OpenLog
By: Nathan Seidle
SparkFun Electronics
Date: September 22nd, 2013
License: This code is public domain but you buy me a beer if you use this and we meet someday (Beerware license).
This example reads the firmware version of the OpenLog without the need for a USB to serial connection.
The firmware version of your OpenLog is very helpful if you need tech support.
Connect the following OpenLog to Arduino:
RXI of OpenLog to pin 2 on the Arduino
TXO to 3
GRN to 4
VCC to 5V
GND to GND
This example code assumes the OpenLog is set to operate in default mode. This is 9600bps
in NewLog mode, meaning OpenLog should power up and output '12<'. This code then sends the
three escape characters and then sends the commands to bring up the help menu '?' and then
looks for the "OpenLog v4.0" text at the top of the menu. It will then print the version
# to the serial terminal.
This code assume OpenLog is in the default state of 9600bps with ASCII-26 as the esacape character.
If you're unsure, make sure the config.txt file contains the following: 9600,26,3,0
Be careful when sending commands to OpenLog. println() sends extra newline characters that
cause problems with the command parser. v2.51 and above ignores \n commands so it should be easier to
talk to on the command prompt level. This example code works with all OpenLog v2 and higher.
*/
#include <SoftwareSerial.h>
//-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
//Connect TXO of OpenLog to pin 3, RXI to pin 2
SoftwareSerial OpenLog(3, 2); //Soft RX on 3, Soft TX out on 2
//SoftwareSerial(rxPin, txPin)
int resetOpenLog = 4; //This pin resets OpenLog. Connect pin 4 to pin GRN on OpenLog.
//-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
int statLED = 13;
void setup() {
pinMode(statLED, OUTPUT);
Serial.begin(9600);
Serial.println("Find OpenLog Firmware Version");
setupOpenLog(); //Resets logger and waits for the '<' I'm alive character
Serial.println("OpenLog online");
gotoCommandMode(); //Puts OpenLog in command mode
OpenLog.println('?'); //Send a character to get help menu
delay(100);
byte counter = 200;
while(OpenLog.available() && counter > 0)
{
byte incoming = OpenLog.read();
if(incoming == 'v') counter = 4; //Get the next four characters
Serial.write(incoming);
counter--;
}
Serial.println();
}
void loop() {
//Do nothing
}
//Setups up the software serial, resets OpenLog so we know what state it's in, and waits
//for OpenLog to come online and report '<' that it is ready to receive characters to record
void setupOpenLog(void) {
pinMode(resetOpenLog, OUTPUT);
OpenLog.begin(9600);
//Reset OpenLog
digitalWrite(resetOpenLog, LOW);
delay(100);
digitalWrite(resetOpenLog, HIGH);
//Wait for OpenLog to respond with '<' to indicate it is alive and recording to a file
while(1) {
if(OpenLog.available())
if(OpenLog.read() == '<') break;
}
}
//This function pushes OpenLog into command mode
void gotoCommandMode(void) {
//Send three control z to enter OpenLog command mode
//Works with Arduino v1.0
OpenLog.write(26);
OpenLog.write(26);
OpenLog.write(26);
//Wait for OpenLog to respond with '>' to indicate we are in command mode
while(1) {
if(OpenLog.available())
if(OpenLog.read() == '>') break;
}
}

6
firmware/Arduino_Examples/Performance_Testing/Buffer_Overrun_Test/Buffer_Overrun_Test.ino
View File

@ -45,16 +45,16 @@ void setup()
{
pinMode(ledPin, OUTPUT);
//Serial.begin(9600); //9600bps is default for OpenLog
Serial.begin(9600); //9600bps is default for OpenLog
//Serial.begin(57600); //Much faster serial, used for testing buffer overruns on OpenLog
Serial.begin(115200); //Much faster serial, used for testing buffer overruns on OpenLog
//Serial.begin(115200); //Much faster serial, used for testing buffer overruns on OpenLog
delay(1000); //Wait a second for OpenLog to init
Serial.println();
Serial.println("Run OpenLog Test");
int testAmt = 30;
int testAmt = 3;
//At 9600, testAmt of 4 takes about 1 minute, 10 takes about 3 minutes
//At 57600, testAmt of 10 takes about 1 minute, 40 takes about 5 minutes
//At 115200, testAmt of 30 takes about 1 minute

97
firmware/Arduino_Examples/Performance_Testing/CommandPrompt_Power/CommandPrompt_Power.ino Normal file
View File

@ -0,0 +1,97 @@
/*
Example of creating a file, reading a file, and reading the disk properties on OpenLog
By: Nathan Seidle
SparkFun Electronics
Date: September 22nd, 2013
License: This code is public domain but you buy me a beer if you use this and we meet someday (Beerware license).
This example puts OpenLog in command mode with and without LED so we can test current
consumption during command prompt.
Connect the following OpenLog to Arduino:
RXI of OpenLog to pin 2 on the Arduino
TXO to 3
GRN to 4
VCC to 5V
GND to GND
This example code assumes the OpenLog is set to operate at 9600bps in NewLog mode, meaning OpenLog
should power up and output '12<'. This code then sends the three escape characters and then sends
the commands to create a new random file called log###.txt where ### is a random number from 0 to 999.
The example code will then read back the random file and print it to the serial terminal.
This code assume OpenLog is in the default state of 9600bps with ASCII-26 as the esacape character.
If you're unsure, make sure the config.txt file contains the following: 9600,26,3,0
Be careful when sending commands to OpenLog. println() sends extra newline characters that
cause problems with the command parser. The new v2.51 ignores \n commands so it should be easier to
talk to on the command prompt level. This example code works with all OpenLog v2 and higher.
*/
#include <SoftwareSerial.h>
//-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
//Connect TXO of OpenLog to pin 3, RXI to pin 2
SoftwareSerial OpenLog(3, 2); //Soft RX on 3, Soft TX out on 2
//SoftwareSerial(rxPin, txPin)
int resetOpenLog = 4; //This pin resets OpenLog. Connect pin 4 to pin GRN on OpenLog.
//-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
int statLED = 13;
void setup() {
pinMode(statLED, OUTPUT);
Serial.begin(9600);
setupOpenLog(); //Resets logger and waits for the '<' I'm alive character
Serial.println("OpenLog online");
}
void loop() {
Serial.println("Going to command mode");
gotoCommandMode(); //Puts OpenLog in command mode
//OpenLog will now be at ~6.7mA
OpenLog.write('p'); //Send a character to get LED to turn on and stay on
//OpenLog will now be at ~7.2mA
while(1); //Freeze
}
//Setups up the software serial, resets OpenLog so we know what state it's in, and waits
//for OpenLog to come online and report '<' that it is ready to receive characters to record
void setupOpenLog(void) {
pinMode(resetOpenLog, OUTPUT);
OpenLog.begin(9600);
//Reset OpenLog
digitalWrite(resetOpenLog, LOW);
delay(100);
digitalWrite(resetOpenLog, HIGH);
//Wait for OpenLog to respond with '<' to indicate it is alive and recording to a file
while(1) {
if(OpenLog.available())
if(OpenLog.read() == '<') break;
}
}
//This function pushes OpenLog into command mode
void gotoCommandMode(void) {
//Send three control z to enter OpenLog command mode
//Works with Arduino v1.0
OpenLog.write(26);
OpenLog.write(26);
OpenLog.write(26);
//Wait for OpenLog to respond with '>' to indicate we are in command mode
while(1) {
if(OpenLog.available())
if(OpenLog.read() == '>') break;
}
}

4
hardware/OpenLog.sch
View File

@ -1,6 +1,6 @@
<?xml version="1.0" encoding="utf-8"?>
<!DOCTYPE eagle SYSTEM "eagle.dtd">
<eagle version="7.5.0">
<eagle version="7.7.0">
<drawing>
<settings>
<setting alwaysvectorfont="no"/>
@ -152,7 +152,7 @@
<layer number="254" name="cooling" color="7" fill="1" visible="yes" active="yes"/>
<layer number="255" name="routoute" color="7" fill="1" visible="no" active="yes"/>
</layers>
<schematic xreflabel="%F%N/%S" xrefpart="/%S">
<schematic xreflabel="%F%N/%S" xrefpart="/%S.%C%R">
<libraries>
<library name="SparkFun">
<packages>