6.9 KiB
6.9 KiB
ambilight
adaligth fastLED sketch
[https://github.com/dmadison/Adalight-FastLED]
/\*
\* Project Adalight FastLED
\* @author David Madison
\* @link github.com/dmadison/Adalight-FastLED
\* @license LGPL - Copyright (c) 2017 David Madison
\*
\* This program is free software: you can redistribute it and/or modify
\* it under the terms of the GNU Lesser General Public License as published by
\* the Free Software Foundation, either version 3 of the License, or
\* (at your option) any later version.
\*
\* This program is distributed in the hope that it will be useful,
\* but WITHOUT ANY WARRANTY; without even the implied warranty of
\* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
\* GNU Lesser General Public License for more details.
\*
\* You should have received a copy of the GNU Lesser General Public License
\* along with this program. If not, see <http://www.gnu.org/licenses/>.
*
*/
#include <Arduino.h>
// \-\-\- General Settings
const uint16_t
Num_Leds = 80; // strip length
const uint8_t
Brightness = 255; // maximum brightness
// \-\-\- FastLED Setings
#define LED_TYPE WS2812B // led strip type for FastLED
#define COLOR_ORDER GRB // color order for bitbang
#define PIN_DATA 6 // led data output pin
// #define PIN_CLOCK 7 // led data clock pin (uncomment if you're using a 4-wire LED type)
// \-\-\- Serial Settings
const unsigned long
SerialSpeed = 115200; // serial port speed
const uint16_t
SerialTimeout = 60; // time before LEDs are shut off if no data (in seconds), 0 to disable
// \-\-\- Optional Settings (uncomment to add)
#define SERIAL_FLUSH // Serial buffer cleared on LED latch
// #define CLEAR\_ON\_START // LEDs are cleared on reset
// \-\-\- Debug Settings (uncomment to add)
// #define DEBUG_LED 13 // toggles the Arduino's built-in LED on header match
// #define DEBUG_FPS 8 // enables a pulse on LED latch
// --------------------------------------------------------------------
#include <FastLED.h>
CRGB leds\[Num_Leds\];
uint8\_t * ledsRaw = (uint8\_t *)leds;
// A 'magic word' (along with LED count & checksum) precedes each block
// of LED data; this assists the microcontroller in syncing up with the
// host-side software and properly issuing the latch (host I/O is
// likely buffered, making usleep() unreliable for latch). You may see
// an initial glitchy frame or two until the two come into alignment.
// The magic word can be whatever sequence you like, but each character
// should be unique, and frequent pixel values like 0 and 255 are
// avoided -- fewer false positives. The host software will need to
// generate a compatible header: immediately following the magic word
// are three bytes: a 16-bit count of the number of LEDs (high byte
// first) followed by a simple checksum value (high byte XOR low byte
// XOR 0x55). LED data follows, 3 bytes per LED, in order R, G, B,
// where 0 = off and 255 = max brightness.
const uint8_t magic\[\] = {
'A','d','a'};
#define MAGICSIZE sizeof(magic)
// Check values are header byte # - 1, as they are indexed from 0
#define HICHECK (MAGICSIZE)
#define LOCHECK (MAGICSIZE + 1)
#define CHECKSUM (MAGICSIZE + 2)
enum processModes_t {Header, Data} mode = Header;
int16_t c; // current byte, must support -1 if no data available
uint16_t outPos; // current byte index in the LED array
uint32_t bytesRemaining; // count of bytes yet received, set by checksum
unsigned long t, lastByteTime, lastAckTime; // millisecond timestamps
void headerMode();
void dataMode();
void timeouts();
// Macros initialized
#ifdef SERIAL_FLUSH
#undef SERIAL_FLUSH
#define SERIAL_FLUSH while(Serial.available() > 0) { Serial.read(); }
#else
#define SERIAL_FLUSH
#endif
#ifdef DEBUG_LED
#define ON 1
#define OFF 0
#define D\_LED(x) do {digitalWrite(DEBUG\_LED, x);} while(0)
#else
#define D_LED(x)
#endif
#ifdef DEBUG_FPS
#define D\_FPS do {digitalWrite(DEBUG\_FPS, HIGH); digitalWrite(DEBUG_FPS, LOW);} while (0)
#else
#define D_FPS
#endif
void setup(){
#ifdef DEBUG_LED
pinMode(DEBUG_LED, OUTPUT);
digitalWrite(DEBUG_LED, LOW);
#endif
#ifdef DEBUG_FPS
pinMode(DEBUG_FPS, OUTPUT);
#endif
#if defined(PIN\_CLOCK) && defined(PIN\_DATA)
FastLED.addLeds<LED\_TYPE, PIN\_DATA, PIN\_CLOCK, COLOR\_ORDER>(leds, Num_Leds);
#elif defined(PIN_DATA)
FastLED.addLeds<LED\_TYPE, PIN\_DATA, COLOR\_ORDER>(leds, Num\_Leds);
#else
#error "No LED output pins defined. Check your settings at the top."
#endif
FastLED.setBrightness(Brightness);
#ifdef CLEAR\_ON\_START
FastLED.show();
#endif
Serial.begin(SerialSpeed);
Serial.print("Ada\\n"); // Send ACK string to host
lastByteTime = lastAckTime = millis(); // Set initial counters
}
void loop(){
t = millis(); // Save current time
// If there is new serial data
if((c = Serial.read()) >= 0){
lastByteTime = lastAckTime = t; // Reset timeout counters
switch(mode) {
case Header:
headerMode();
break;
case Data:
dataMode();
break;
}
}
else {
// No new data
timeouts();
}
}
void headerMode(){
static uint8_t
headPos,
hi, lo, chk;
if(headPos < MAGICSIZE){
// Check if magic word matches
if(c == magic\[headPos\]) {headPos++;}
else {headPos = 0;}
}
else{
// Magic word matches! Now verify checksum
switch(headPos){
case HICHECK:
hi = c;
headPos++;
break;
case LOCHECK:
lo = c;
headPos++;
break;
case CHECKSUM:
chk = c;
if(chk == (hi ^ lo ^ 0x55)) {
// Checksum looks valid. Get 16-bit LED count, add 1
// (# LEDs is always > 0) and multiply by 3 for R,G,B.
D_LED(ON);
bytesRemaining = 3L * (256L * (long)hi + (long)lo + 1L);
outPos = 0;
memset(leds, 0, Num_Leds * sizeof(struct CRGB));
mode = Data; // Proceed to latch wait mode
}
headPos = 0; // Reset header position regardless of checksum result
break;
}
}
}
void dataMode(){
// If LED data is not full
if (outPos < sizeof(leds)){
ledsRaw\[outPos++\] = c; // Issue next byte
}
bytesRemaining--;
if(bytesRemaining == 0) {
// End of data -- issue latch:
mode = Header; // Begin next header search
FastLED.show();
D_FPS;
D_LED(OFF);
SERIAL_FLUSH;
}
}
void timeouts(){
// No data received. If this persists, send an ACK packet
// to host once every second to alert it to our presence.
if((t - lastAckTime) >= 1000) {
Serial.print("Ada\\n"); // Send ACK string to host
lastAckTime = t; // Reset counter
// If no data received for an extended time, turn off all LEDs.
if(SerialTimeout != 0 && (t - lastByteTime) >= (uint32_t) SerialTimeout * 1000) {
memset(leds, 0, Num_Leds * sizeof(struct CRGB)); //filling Led array by zeroes
FastLED.show();
mode = Header;
lastByteTime = t; // Reset counter
}
}
}
arduino nano clone
- use the old bootloader (or update it)
- sometimes the sketch get lost?, reflash it